Knots 2 - intro
Back to net & rope index
Qualities of a knot
Knots must have 3 qualities:
And one other: important knots should be do-able one-handed and blindfolded. Emergencies occur in the black of night, in a gale, with you holding onto something with one hand while tying something down with the other ... while reading the book Knots, ties and splices.
Glossary
Bight: is formed when you lay the end back on the standing part (of the rope).
Bitter end: the other end of the rope; the end not being used; the end not in your hand.
Belay: attach a rope to a cleat.
Bend: we bend (tie) two ropes together.(The anchor bend is actually a hitch.)
Eye: very small loop.
Hitch: tie a rope to a solid object, like a hitching post.
Eye: very small loop.
Lashing: a knot which binds 2 or more spars or timbers.
Loop: when the standing part crosses over itself (a bight in which the end crosses over the standing part).
Reef knot: A reef knot is good for reefing, and 'good-for-nothing' else.
Seizing: a small alshing that binds 2 ropes or a rope to a post.
Slippery: means a bight is left in the rope to allow you to pull that end free, as in the knot used to tie shoelaces.
Snugging: carefully tightening the new knot till all parts are firmly in their proper place. Loose knots, such as an unsnugged bowline for rockclimbing, can give-way suddenly with fatal consequences.
Splice: a join of 2 ropes or one rope with itself to form an eye, in which join the rope is opened to expose its strands which are then interwoven to form the join. (See Splices)
Standing part: the main part of the rope, excluding both end sections.
Toggle: small piece of wood or metal inserted thru a knot to help it hold.
Whipping: to stop the end of a rope unravelling by wrapping it with twine wound around it (or with tape as a temporary meazure).
Making knots
StandingPart not found OverhandLoop not found UnderhandLoop not found OverhandKnot not found Overhand knot
Knots are formed by using 3 simple turns: bight, loop, over/under-hand.
Even the most complicated knots can be analysed and learnt using these 3 terms.
Bight lays the end of the rope against the standing part (long stretch of rope).
Loops, underhand loop and overhand loop, are named according to whether you pass the end under or over the standing part.

Examples:
A square/reef knot is 2 interwoven bights.
Sheet bend and bowline are a [bight + loop].
Clove hitch = 2 loops.
Slipknot = overhand knot tied around the standing part.
Timber hitch and 2 half-hitches are variations of the overhand knot.

Practise
Practising with a cord or rope is essential for understanding, remembering and mastering knots. Always carry some cord in your pocket so you can practise in idle moments while waiting for someone or something.
When you know all your knots from memory, practise for speed. Time yourself. Practise with eyes shut. Practise one-handed with eyes shut.
Now, can you tie the correct knot with maximum speed in the darkness of night in a gale ?
That is the test.
Back to Contents
Whipping
whipping 1 not found whipping 2 not found whipping 3 not found Rope ends of synthetic fibre (such as nylon, polyester) can usually be sealed by a hot iron. Less efficient is a flame.

Natural fibres need to be whipped to prevent their unravelling. Never use a rope before its ends are whipped. As a temporary meazure, a poor one, wind duct tape around it.

The simplest method, shown here, is called American whipping, but the best is the back splice (see Contents/Splices/Back splice).
whipping4 not found whipping5 not found Back to Contents
Coiling rope
Coiling not found To coil rope, first shake it out in a straight line and remove the kinks. This may need some twisting to remove the 'memory' of previous coiling.

Hold one end in your left hand, pull in enough rope to make a loop about 450mm long. [Or use your arms stretched sideways as a meazure for a larger loop.] As you place the loop into your left hand, roll (twist) the rope a 1/2 turn toward you with your right thumb and forefinger. This will counteract the twist you put into the rope as you made the loop. It will also help to eliminate kinks.

To make a flat coil (see drawing) lay the outer circle first and coil in toward the center in a clockwise direction. Give a 1/2 turn to each coil to eliminate kinks. If your coil is too loose, you can tighten it by twisting the center with the palm of your hand.

To uncoil, pull the end from the center.
Back to Contents
Caring for rope
Good ropes are expensive. In rockclimbing and sailing, your life may depend upon them. Treat with love.

Never step on a rope.
Keep your rope clean, free of grit (which cuts the fibres) and free of grease. If damp, do not coil or store until thoroughly dried. Do not dry close to a fire, which may overheat the fibres and cause deterioration such as hardening and weakening.

Store by hanging on a cylindrical block or thick peg (to prevent kinking); in a dry place. Never drop loosely on the floor, where it will kink, and usually be walked upon. If you are careless with your ropes, so will others be.
When stored, you should be able to access them quickly in case of emergency (such as fire or rescue) and be in such condition that you should be able to pay it out smoothly, without any kinks or entanglements.
Back to Contents
Making rope
making_rope1 not found Making a rope requires some easily-made equipment. 12mm thick wood with stiff wire for hooks (such as heavy fencing wire bent with use of a vise with stout pliers).

For the rope use heavy string or twine. Tie one end to one of the hooks and loop it back and forth between the hook and the awl. About 3 strands to each hook will make a medium-sized rope.

Insert the crank handle in the cranks and start rotating it. Hold the strands apart with the rope wrench until they become fairly tight. Then take hold of the strands behind the wrench – that is, on the side away from the 'machine' – and begin twisting them slowly together as the wrench is moved forward.

making_rope2 not found The rope will go into shape itself and remain there, but the wrench should be used to ensure even twisting and to prevent kinks. The cranks should be turned slowly while the rope is being formed.

When the rope is complete, take it off the hooks and whip the ends to prevent fraying.

Back to Contents

Back to net & rope index