End knots & loops
Back to net & rope index
End knots
These knots are usually used to prevent slipping; may be tied at either end or in the standing part, to limit sliding thru a block, hole or part of another knot (as in fisher's knot), or to temporarily stop ends fraying on a newly cut rope.
Overhand not found fig8 not found Stevedores not found
Overhand knot
Basic turn in knotting, and the simplest end knot.
Figure-8 knot
Often used for ropes having lariat loops, or for string tying packages with a slipknot.
Stevedore's knot
A fig-8 knot with an extra loop, making it larger for an end-knot and looking chain-like.
Back to Contents
Wall Knot not found
SingleMatthewWalkerKnot not found
DoubleMatthewWalkerKnot not found
These 3 knots are firm, round and semipermanent stopper knots tied with the end strands of the rope. Snug each carefully so that the strands tighten evenly. The ends can be trimmed or twisted together again for whipping (as in the Double Matthew Walker knot).
Wall knot
Each strand runs thru the bight of the next strand.
Single Matthew Walker knot
This is the wall knot with one extra step. Before snugging the wall knot, carry each strand end thru the bight ahead of it, so that each strand runs under 2 bights.
Double Matthew Walker knot
Tie the Single but before snugging, carry the strands thrua 3rd bight (their own) to give 3 interlocked overhand knots.
Back to Contents
Back to Contents
Knots for loops
These knots are for holding loops like a lariat loop, but either fixed or sliding.The bowline is a must for rescue work and yatching.
bowline 1 not found bowline 2 not found
Bowline
Never slips or jams if snugged properly, and is therefore ideal for rescues. Can be easily undone. Form overhand loop then take end up thru eye, around standing part and down thru eye.
One-handed method which is faster: To learn, tie the bitter end to a post or chair, and hold standing part taut in left hand. Hold the free end in the curled little finger of right hand but have 150mm dangling under index finger. Place wrist on standing part and pass index finger left-wise to form a loop in the left's standing part. (Try it.) This simple movement does two actions at the same time. The eye is formed with the end already up thru the eye, and with the index finger curling the end around the standing part. Use the index finger to flip the end down thru the eye again. Snug carefully – your life may some day depend upon it.
Back to Contents
French bowline
FrenchBowline 1 not found FrenchBowline 2 not found FrenchBowline 3 not found FrenchBowline 4 not found
A double bowline with 2 nonslip loops, equal size fora person to sit with a leg in each loop, or unequal size to sit in one loop with the other as a back support. (Three loops give 2 leg loops plus one back loop.) Good for rescue work or working on heights.
Begin with an overhand loop but pass the end thru the eye 2x before bringing it back around the standing part and thru the original eye. The bottom drawing gives the finished knot ready to be snugged.
Back to Contents
Bowline on a bight
BowlineOnBight 1 not found BowlineOnBight 2 not found BowlineOnBight 3 not found Wind a generous bight around, forming two loops of equal size. Pass the end of the bight thru the eye, then pass the 'bights' of the two loops thru the first bight. Snug down before putting weight on it.
Back to Contents
RunningBowline 1 not found RunningBowline 2 not found
Running bowline
Has the standing part sliding freely thru the bowline to provide a noose. The 2nd diagram is quicker by not needing to pass the bitter end thru the loop.
Back to Contents
LariatLoop 1not found LariatLoop 2 not found
Lariat loop
This running knot is an overhand knot with the free end brought back. The end should then be given a stopper such as figure-8 or Matthew Walker knot. It should be pulled or hammered very snugly for lariat use. To finish the lariat, draw a bight thru the large loop to form the running noose.
ManHarnessKnot 1 not found ManHarnessKnot 2 not found
Man-harness knot
ManHarnessKnot 3 not found Main use is to make a noose in the middle of a hauling rope, to attach another means of hauling. Form an underhand loop; grasp the loop at A and lay it over the arrowed part to get the middle diagram. Grasp rope at B and draw it up under and over as shown at the bottom diagram. This forms a bight which becomes the loop for your shoulder or an attachment.Snug tightly before using.
Back to Contents
Back to net & rope index