Other knots
Back to net & rope index
Other knots
MillersKnot 1 not found MillersKnot 2 not found MillersKnot 3 not found
Miller's knot
Miller's and strangle are closely related to the clove hitch, and are for tying sacks with heavy sring or cord. In the miller's, the first turn around the sack leads over the forefinger and the others pass under all fingers. In the middle drawing, forefinger A is about to draw the cord end B under C to complete the knot. To make untying easy, draw a bight instead of the end underneath.
Back to Contents
StrangleKnot 1 not found StrangleKnot 2 not found
Strangle knot
This has many applications, such as emergency whipping, a tie for a finger bandage, or instead of a miller's knot. Cross the 2nd turn over the firest and pull the end under both turns. To make untying easy, draw a bight instead of the end underneath.
Back to Contents
BarrelSling 1 not found BarrelSling 2 not found BarrelSling 3 not found
Barrel sling
For heavy objects:
  • Lay a length along the ground.
  • Place the barrel on it at a distance from one end about 2.5x its height.
  • Bring the rope ends over the top and form an overhand crossing.
  • Grasp the rope with one hand at A and the other at B (middle drawing) and pull in opposite directions.
  • Carry the halves down over the sides of the barrel, as shown by the arrows in the top drawing. This should result be a turn as at C in the bottom drawing on both sides of the barrel.
  • Finish with a bowline as shown at the bottom.
  • If the sling is to be used on a slippery object, pass 2 loops around it.
Back to Contents
PackersKnot not found StrapKnotStrapKnot not found GirthHitch not found
Packer's knot
Just a figure-8 knot tied around the stadnding part, this is one of the best ways to begin to wrap a package or a swag. Make the 1st turn by passing the loop of the packer's knot around the package and pulling tight.
Back to Contents
Strap knot
For joining 2 flat straps, the strap knot is 2 interlocked loops pushed together. Safe enough to use for an emergency rope.
Girth hitch
To attach a leather strap or rope to a metal ring. Used to tie a cinch strap of a western saddle.
Back to Contents
DiamondHitch 1 not found DiamondHitch 2 not found DiamondHitch 3 not found DiamondHitch 4 not found
Diamond hitch
For loading packhorses, the diamond hitch is useful for lashing your pack to a 6-point frame.Its advantage is that a pull on any section of the line makes every other section tighter:
  • Tie one rope end at point 1, using a clove hitch.
  • Loop the rope over points 2 & 3 as shown in A.
  • Before pulling the line thru the bight between points 1 & 2, twist the 2 center strands 2 or 3 times.
  • Loop the rope over the other points in numerical order as shown.
  • When the hitch is nearly complete, pull the rope to tighten all sides and tie it at point 1 (over the starting hitch) with a hitch or knot.
The bottom drawing shows the diamond hitch completed around a pack. Note the diamond in the center.
Back to Contents
Sheepshank
Sheepshank 1 not found Sheepshank 2 not found
Sheepshank 3 not found Used to shorten a rope that is fastened at both ends, and also to provide a purchase to run the rope thru to tighten that rope in a manner of a block and tackle (pulley):
  • Take up the slack as in 1.
  • Make an underhand loop as shown at B in 2, and slide it over the B1 bight and pull tight.
  • Do the same at the other end, to complete the knot.
  • To make more secure, add a second hitch at each end, as in 3.
Back to Contents
Marling
Marling not found Used by seamen to lash hammocks or other gear, marling is a series of overhand knots. The end of the rope should always come out from underneath the hitch.
Back to Contents
Toggles 1 not found Toggles 2 not found
Toggles
A toggle is a small piece of wood or metal usually used to lock a knot that may need to be loosened quickly or to help it hold more securely. Two examples are shown. At left is one end of a sheepshank with a toggle inserted to ensure the knot does not slip. At right is a lark's head with toggle. Removing the toggle releases the hitch.
Back to Contents
MarlinSpikeHitch not found
Marlin spike hitch
For a purchase on a rope before hauling on it. Can be used for tightening a lashing. For the spike use a marlin or a tent peg.
Back to Contents
Belaying 1 not found
Belaying
A means of attaching a rope to a cleat. Begin with a turn as shown, then make 1 or 2 fig-8 turns in the 2nd drawing. Finish with a hitch (underhand loop) pulled snug, unless the rope needs to be released quickly.
Back to Contents
RoundSeizing 1 not found RoundSeizing 2 not found RoundSeizing 3 not found
Round seizing
A seizing is a small lashing that binds 2 ropes or, sometimes, a lashing that holds a rope to a post. Seizings are often used to make a permanent eye in a rope. Cord or heavy twine can be used. To make a ropund seizing for an eye:
  • Form a bight.
  • Splice an eye in the end of the seizing material (see splicing). If the cord is too small, use a timber hitch.
  • Take 8 or 10 turns around both sides of the bight.
  • At the finish of the turns, bring the end down betweenthe loops and up thru the eye.
  • Snug up all the loops as shown and leave the end protuding as at A.
  • Take a 2nd series of turns, called riders, over the first ones, laying the turns in the grooves as shown at B. Do not pull them so tightly that they separate the first series of turns.
  • Finish the riders with a tuck-under as shown at D. This will leave the end as at C.
  • Take 2 or 3 frapping turns, see bottom drawing, to form a clove hitch.
  • Take the end down on to one of the ropes and fasten with another clove hitch.
Back to Contents
RackingSeizing 1 not found RackingSeizing 2 not found RackingSeizing 3 not found
Racking seizing
Used to lash together 2 parallel ropes:
  • Begin with an eye splice in the seizing material and then wrap it around the ropes in a fugure-8 pattern as in Fig 1.
  • Make as many turns as necessary.
  • Then bring the turns together as in Fig 2.
  • Wind round and round back toward the eye splice, laying the lashing into the spaces between the turns of the first set as indicated by the numbers in fig 2.
  • The seizing may be finished by making the same frapping turns and fastening used for round seizing.

Fig 3 shows the round seizing in cross-section; the fig-8 turns are shown by the white band and the round turns by the black band.
Back to Contents

Back to net & rope index