Knots & hitches
Back to net & rope index
Knots must have 3 qualities:
And one other: important knots should be do-able one-handed and blindfolded. Emergencies occur in the black of night, in a gale, with you holding onto something with one hand while tying it down with the other. ( And your other hand is holding a book Knots, ties and splices - learn your knots now !! )

A reef knot is good for reefing, and 'good-for-nothing' else.

snugging: carefully tightening the new knot till all parts are firmly in their proper place. Loose knots, such as a bowline used in rockclimbing, can give-way suddenly with fatal consequences.
Bight: is formed when you lay the end back on the standing part (of the rope).
Standing part: the main part of the rope, excluding the end section.
Bitter end: the other end of the rope; the end not being used; the end not in your hand.
Slippery: means a bight is left in the rope to allow you to pull that end free, as in the knot used to tie shoelaces.
Contents
Making knots
Bight
Overhand loop
Underhand loop
Overhand knot
Whipping
Coiling rope
Caring for rope
Making rope
End knots
Overhand knot
Figure-8 knot
Stevedore's knot
Wall knot
S. Matt Walker
D. Matt Walker
Knots for loops
Bowline
French bowline
Bowline on a bight
Running bowline
Lariat loop
Man-harness knot
Tie ropes to objects
Half-hitch
Two half-hitches
Round turn &  "
Timber hitch
Killick hitch
Stuns'l hitch
Clove hitch
Clove hitch o'bar
Slippery half-hitch
Slip knot
Pipe hitch
Masthead knot
Rolling hitch
Stopper hitch
Hitching tie
Anchor bend
Single blackwall
Double blackwall
Cat's-paw
Thames hitch
Join ropes
Square/Reef knot
Shoestring knot
Surgeon's knot
Sheet bend
Slippery   "
Fisher's knot
S. Carrick bend
D. Carrick bend
Other knots
Miller's knot
Strangle knot
Barrel sling
Packer's knot
Strap knot
Girth hitch
Diamond hitch
Sheepshank
Marling
Toggles
Marlin spike hitch
Belaying
Round seizing
Racking seizing
Splices
Short splice
Long splice
Back splice
Eye splice
Lashings
Diagonal lashing
Square lashing
Shear lashing
Tripod lashing
Climbing knots
See 3 bowlines:
3 bowlines
Prusik knot/loop
Tarbuck knot
Alpine butterfly

Making rope
making_rope1 not found Making a rope requires some easily-made equipment. 12mm thick wood with stiff wire for hooks (such as heavy fencing wire bent with use of a vise with stout pliers).

For the rope use heavy string or twine. Tie one end to one of the hooks and loop it back and forth between the hook and the awl. About 3 strands to each hook will make a medium-sized rope.

Insert the crank handle in the cranks and start rotating it. Hold the strands apart with the rope wrench until they become fairly tight. Then take hold of the strands behind the wrench – that is, on the side away from the 'machine' – and begin twisting them slowly together as the wrench is moved forward.

making_rope2 not found The rope will go into shape itself and remain there, but the wrench should be used to ensure even twisting and to prevent kinks. The cranks should be turned slowly while the rope is being formed.

When the rope is complete, take it off the hooks and whip the ends to prevent fraying.
Back to Contents
Whipping
whipping 1 not found whipping 2 not found whipping 3 not found Rope ends of synthetic fibre (such as nylon, polyester) can usually be sealed by a hot iron. Less efficient is a flame.

Natural fibres need to be whipped to prevent their unravelling. Never use a rope before its ends are whipped. As a temporary meazure, a poor one, wind duct tape around it.

The simplest method, shown here, is called American whipping, but the best is the back splice (see Contents/Splices/Back splice).
whipping4 not found whipping5 not found Back to Contents
Coiling rope
Coiling not found To coil rope, first shake it out in a straight line and remove the kinks. This may need some twisting to remove the 'memory' of previous coiling.

Hold one end in your left hand, pull in enough rope to make a loop about 450mm long. [Or use your arms stretched sideways as a meazure for a larger loop.] As you place the loop into your left hand, roll (twist) the rope a 1/2 turn toward you with your right thumb and forefinger. This will counteract the twist you put into the rope as you made the loop. It will also help to eliminate kinks.

To make a flat coil (see drawing) lay the outer circle first and coil in toward the center in a clockwise direction. Give a 1/2 turn to each coil to eliminate kinks. If your coil is too loose, you can tighten it by twisting the center with the palm of your hand.

To uncoil, pull the end from the center.
Back to Contents
Caring for rope
Good ropes are expensive. In rockclimbing and sailing, your life may depend upon them. Treat with love.

Never step on a rope.
Keep your rope clean, free of grit (which cuts the fibres) and free of grease. If damp, do not coil or store until thoroughly dried. Do not dry close to a fire, which may overheat the fibres and cause deterioration such as hardening and weakening.

Store by hanging on a cylindrical block or thick peg (to prevent kinking); in a dry place. Never drop loosely on the floor, where it will kink, and usually be walked upon. If you are careless with your ropes, so will others be.
When stored, you should be able to access them quickly in case of emergency (such as fire or rescue) and be in such condition that you should be able to pay it out smoothly, without any kinks or entanglements.
Back to Contents
Bight, loop, overhand
StandingPart not found OverhandLoop not found UnderhandLoop not found OverhandKnot not found
Knots are formed by using 3 simple turns: bight, loop, overhand.
Even the most complicated knots can be analysed and learnt using these 3 terms.
The bight lays the end of the rope against the standing part (long stretch of rope).
Loops, underhand loop and overhand loop, are named according to whether you pass the end under or over the standing part.

Examples:
A square knot is 2 interwoven bights.
Sheet bend and bowline are a [bight + loop].
Clove hitch = 2 loops.
Slipknot = overhand knot tied around the standing part.
Timber hitch and 2 half-hitches are variations of the overhand knot.

Practise
Practising with a cord or rope is essential for understanding, remembering and mastering knots. Always carry some cord in your pocket so you can practise in idle moments while waiting for someone or something.
When you know all your knots from memory, practise for speed. Time yourself. Practise with eyes shut. Practise one-handed with eyes shut.
Now, can you tie the correct knot with maximum speed in the darkness of night in a gale ?
That is the test.
Back to Contents
End knots
These knots are usually used to prevent slipping; may be tied at either end or in the standing part, to limit sliding thru a block, hole or part of another knot (as in fisher's knot), or to temporarily stop ends fraying on a newly cut rope.
Overhand not found fig8 not found Stevedores not found
Overhand knot
Basic turn in knotting, and the simplest end knot.
Figure-8 knot
Often used for ropes having lariat loops, or for string tying packages with a slipknot.
Stevedore's knot
A fig-8 knot with an extra loop, making it larger for an end-knot and looking chain-like.
Back to Contents
Wall Knot not found
SingleMatthewWalkerKnot not found
DoubleMatthewWalkerKnot not found
These 3 knots are firm, round and semipermanent stopper knots tied with the end strands of the rope. Snug each carefully so that the strands tighten evenly. The ends can be trimmed or twisted together again for whipping (as in the Double Matthew Walker knot).
Wall knot
Each strand runs thru the bight of the next strand.
Single Matthew Walker knot
This is the wall knot with one extra step. Before snugging the wall knot, carry each strand end thru the bight ahead of it, so that each strand runs under 2 bights.
Double Matthew Walker knot
Tie the Single but before snugging, carry the strands thrua 3rd bight (their own) to give 3 interlocked overhand knots.
Back to Contents
Back to Contents
Joining ropes
These knots are for tying 2 rope ends together, applicable to 2 ends of the same rope or to 2 different ropes.
Each has its own advantages and disadvantages, so learning when to use or not to use a knot, is important.
Example
The square knot is always used in first aid to tie bandages because it holds well if the strain is always in one (longitudinal) direction; and it loosens easily by pulling one end towards the other end. This knot is also used for reefing sails, but must not be used for anything else on board. Useless for tying parcels because you cannot make the string tight enough. For that you need a surgeon's knot.
Back to Contents
SquareKnot 1 not found SquareKnot 2 not found SquareKnot 3 not found
_____________
Square or reef knot
Put 2 ropes together, left over right, then go back but putting right over left. Never do two left-over-rights because this, a granny knot, often slips or becomes difficult to undo. To loosen, push the ends towards the knot or pulling one end toward the other end.
Back to Contents
ShoestringKnot 1 not found ShoestringKnot 2 not found ShoestringKnot 3 not found ShoestringKnot 4 not found
_____________
Shoestring knot
A square knot with slippery ends. Left-over-right then right-over-left, but the second time use loops. This is done by forming loop A first then passing the standing part of B around it, and thru its own bight. Do not let B's end come thru the bight. Now tighten.
Back to Contents
Surgeons Knot not found
Surgeon's knot
A square knot with an extra twist in the first left-over-right. Used by surgeon's to hold the twine tight while adding the right-over-left.
Useful for tying parcels. Do the first left-over-right with an extra twist, pull tight, then jerk the ends in a swivel action to pull in opposite directions. This makes the loops grip to prevent slipping. Then do the second overhand to complete the knot. Pull tight.
Back to Contents
SheetBend 1 not found SheetBend 2 not found SheetBend 3 not found SheetBend 4 not found
_____________
Sheet bend
The most important knot for joining 2 rope ends, particularly if the ropes have different diameters. Bend = to tie; sheet = ropes attached to the lower ends of the sails to pull them taut.(Halyards are attached to the top of the sails to pull them up the mast.)
Begin with the bight in the left rope. Pass the right rope up thru the bight and around the back of both parts of the bight. Then thread the end of the right rope under itself, that is, between the bight of the left rope and itself.
This is also called the weaver's knot, done with different hand actions to give the same knot. Place the larger rope in the left hand.
Back to Contents
SlipperySheetBend not found
Slippery sheet bend
An ordinary sheet bend with a bight added to ease its release. Just tug on the end of the bight. Handy to quick release or when frequently tying and untying.
FishersKnot not found
Fisher's knot
Used for joining 2 fine lines such as fishing leaders. Two overhand knots, one on each line, around the other line.Pull each knot taut separately until snug, then pull the standing parts till the knots catch up against each other.
Back to Contents
SingleCarrickBend 1 not found SingleCarrickBend 2 not found SingleCarrickBend 3 not found
_____________
Single Carrick bend
These 2 Carrick bends are used on large hawsers for towing ships. They are among the strongest knots but need to have ends seized to their standing parts. (You would not want to untie them often.) Begin with a bight in the left rope then weave the right rope thru as shown.
Back to Contents
DoubleCarrickBend 1 not found DoubleCarrickBend 2 not found DoubleCarrickBend 3 not found
_____________
Double Carrick bend
Like the Single Carrick but instead of a bight, begin with an underhand loop. This gives 2 crossovers instead of one.
Back to Contents

Back to Contents
Tying ropes to objects
Knots for tying ropes to poles or rings are called hitches. Important in pioneering, bygone forestry and trekking.
HalfHitch not found
Half hitch
useful as temporary attaching knot, the half-hitch begins many other knots. It will hold against a steady pull on the standing part, especially with a stopper such as figure-8 or stevedore's knot (in the end). A favorite is a round-turn with 2 half-hitches.
SlipperyHalfHitch not found SlipperyHalfHitch not found
Slippery half-hitch
By now you should be able to imagine how to do this. An overhand knot with a bight at the end to run thru the eye of the knot.
TwoHalfHitches not found
Two half-hitches
Very reliable for attaching a rope to a pole or mooring. To finish, push the 2 half-hitches together and snug them by pulling on the standing part.
 
Round turn and 2 half-hitches
Wind the rope around the post 1.5 times (360+180 degrees) then do 2 half-hitches. This provides friction to absorb the jerking of the standing part.
Back to Contents
TimberHitch not found TimberHitch not found
Timber hitch
For strain parallel to log. Important for dragging a heavy object like a log, it will hold firmly so long as there is a steady pull. Slackening or jerking may loosen it. Use a killich (anchor) hitch for dragging, by adding a hitch to the front of the log or similar, to guide it.
Stuns'l hitch
stunsl_bend.gif not found For strain perpendicular to log.
Back to Contents
CloveHitch not found CloveHitch not found
Clove hitch
Widely used, by running around the post 2x in only one direction, it puts little strain on the rope, and bites into the post instead of cutting back against the rope. If the top of the post is within reach, you can drop 2 underhand loops over it, and draw them tight.
Back to Contents
CloveHitchOverBar not found
Clove hitch over bar
Threading the end under the standing part, is necessary when the end of the post is not accessible.
Back to Contents
Slipknot
SlipKnot 1 not found SlipKnot 3 not found SlipKnot 2 not found
Unless a strain is kept on it, it may slide; thus inferior to the 2-half-hitches. Fig B shows it as an overhand knot around the standing part. Fig A1 holds better by using the standing part first then the loop is placed over the object. Tie a stopper for security, before beginning.
Back to Contents
PipeHitch 1 not found PipeHitch 2 not found
Pipe hitch
Useful for lifting a bar or post straight up, such as when pulling it from the ground. Take 4 or 5 turns around the post; cross the end over then 2 half-hitches. An added hitch is usually taken further up to keep the post vertical.
Back to Contents
MastheadKnot not found
Masthead knot
Now only for decorative purposes but was used as a strap around a temporary masthead to which straps could be fastened.Begins with 3 overlapping hitches. The inner bights of the 2 outer hitches are led in regualr sequence over and under to the opposite sides of the knot, while the upper bight of the center hitch is extended.
Back to Contents
RollingHitch 1 not found RollingHitch 2 not found RollingHitch 3 not found RollingHitch 4 not found
Rolling or taut-line hitch
These 2 hitches are the same knot used in different ways Fig A, B, C show the rolling hitch around a pole. In a rescue this could be tied in a taut rope, using only one hand to wrap the rope around your body.
Fig D shows the taut-line hitch to tighten tent ropes.
StopperHitch not found
Stopper hitch
Same as taut-line hitch except that turns 1 and 2 are reversed. Neither hitches will slip down even on smooth surfaces.
Back to Contents
HitchingTie 1 not found HitchingTie 2 not found HitchingTie 3 not found
Hitching tie
Common for hitching animals.The second move forms a slippery hitch until the end is brought down thru the eye, locking it.
Back to Contents
AnchorBend not found
Anchor bend
Also called fisher's bend,is one of the strongest hitches. Two turns around the post or ring, then bring the end over the standing part and thru the loop. Finish with 2 half-hitches.
Back to Contents
SingleBlackwall 1 not found SingleBlackwall 2 not found
Single blackwall
Half-hitch over a hook; looped from around the back of the hook. Will hold only under constant strain. A stopper will help. Untrustworthy.
Back to Contents
DoubleBlackwall 1 not found DoubleBlackwall 2 not found DoubleBlackwall 3 not found
Double blackwall
Looped from around the front of the hook. A little safer than the single, but not much. Bowline is better.
Back to Contents
CatsPaw not found
Cat's-paw
Better than either blackwalls; will not slip not need constant strain. Two loops turned inwards one or two complete turns; hang eyes over hook.
Back to Contents
Thames hitch not found
Thames hitch
Or tugboat hitch,; a mooring hitch to a post; 2 turns around post with a single line; make a bight and pass under standing part, then back over post. Pull tight.
Back to Contents
Knots for loops
These knots are for holding loops like a lariat loop, but either fixed or sliding.The bowline is a must for rescue work and yatching.
bowline 1 not found bowline 2 not found
Bowline
Never slips or jams if snugged properly, and is therefore ideal for rescues. Can be easily undone. Form overhand loop then take end up thru eye, around standing part and down thru eye.
One-handed method which is faster: To learn, tie the bitter end to a post or chair, and hold standing part taut in left hand. Hold the free end in the curled little finger of right hand but have 150mm dangling under index finger. Place wrist on standing part and pass index finger left-wise to form a loop in the left's standing part. (Try it.) This simple movement does two actions at the same time. The eye is formed with the end already up thru the eye, and with the index finger curling the end around the standing part. Use the index finger to flip the end down thru the eye again. Snug carefully – your life may some day depend upon it.
Back to Contents
French bowline
FrenchBowline 1 not found FrenchBowline 2 not found FrenchBowline 3 not found FrenchBowline 4 not found
A double bowline with 2 nonslip loops, equal size fora person to sit with a leg in each loop, or unequal size to sit in one loop with the other as a back support. (Three loops give 2 leg loops plus one back loop.) Good for rescue work or working on heights.
Begin with an overhand loop but pass the end thru the eye 2x before bringing it back around the standing part and thru the original eye. The bottom drawing gives the finished knot ready to be snugged.
Back to Contents
Bowline on a bight
BowlineOnBight 1 not found BowlineOnBight 2 not found BowlineOnBight 3 not found Wind a generous bight around, forming two loops of equal size. Pass the end of the bight thru the eye, then pass the 'bights' of the two loops thru the first bight. Snug down before putting weight on it.
Back to Contents
RunningBowline 1 not found RunningBowline 2 not found
Running bowline
Has the standing part sliding freely thru the bowline to provide a noose. The 2nd diagram is quicker by not needing to pass the bitter end thru the loop.
Back to Contents
LariatLoop 1not found LariatLoop 2 not found
Lariat loop
This running knot is an overhand knot with the free end brought back. The end should then be given a stopper such as figure-8 or Matthew Walker knot. It should be pulled or hammered very snugly for lariat use. To finish the lariat, draw a bight thru the large loop to form the running noose.
ManHarnessKnot 1 not found ManHarnessKnot 2 not found
Man-harness knot
ManHarnessKnot 3 not found Main use is to make a noose in the middle of a hauling rope, to attach another means of hauling. Form an underhand loop; grasp the loop at A and lay it over the arrowed part to get the middle diagram. Grasp rope at B and draw it up under and over as shown at the bottom diagram. This forms a bight which becomes the loop for your shoulder or an attachment.Snug tightly before using.
Back to Contents
Other knots
MillersKnot 1 not found MillersKnot 2 not found MillersKnot 3 not found
Miller's knot
Miller's and strangle are closely related to the clove hitch, and are for tying sacks with heavy sring or cord. In the miller's, the first turn around the sack leads over the forefinger and the others pass under all fingers. In the middle drawing, forefinger A is about to draw the cord end B under C to complete the knot. To make untying easy, draw a bight instead of the end underneath.
Back to Contents
StrangleKnot 1 not found StrangleKnot 2 not found
Strangle knot
This has many applications, such as emergency whipping, a tie for a finger bandage, or instead of a miller's knot. Cross the 2nd turn over the firest and pull the end under both turns. To make untying easy, draw a bight instead of the end underneath.
Back to Contents
BarrelSling 1 not found BarrelSling 2 not found BarrelSling 3 not found
Barrel sling
For heavy objects:
  • Lay a length along the ground.
  • Place the barrel on it at a distance from one end about 2.5x its height.
  • Bring the rope ends over the top and form an overhand crossing.
  • Grasp the rope with one hand at A and the other at B (middle drawing) and pull in opposite directions.
  • Carry the halves down over the sides of the barrel, as shown by the arrows in the top drawing. This should result be a turn as at C in the bottom drawing on both sides of the barrel.
  • Finsih with a bowline as shown at the bottom.
  • If the sling is to be used on a slippery object, pass 2 loops around it.
Back to Contents
PackersKnot not found StrapKnot not found GirthHitch not found
Packer's knot
Just a figure-8 knot tied around the standing part, this is one of the best ways to begin to wrap a package or a swag. Make the 1st turn by passing the loop of the packer's knot around the package and pulling tight.
Back to Contents
Strap knot
For joining 2 flat straps, the strap knot is 2 interlocked loops pushed together. Safe enough to use for an emergency rope.
Girth hitch
To attach a leather strap or rope to a metal ring. Used to tie a cinch strap of a western saddle.
Back to Contents
DiamondHitch 1 not found DiamondHitch 2 not found DiamondHitch 3 not found DiamondHitch 4 not found
Diamond hitch
For loading packhorses, the diamond hitch is useful for lashing your pack to a 6-point frame.Its advantage is that a pull on any section of the line makes every other section tighter:
  • Tie one rope end at point 1, using a clove hitch.
  • Loop the rope over points 2 & 3 as shown in A.
  • Before pulling the line thru the bight between points 1 & 2, twist the 2 center strands 2 or 3 times.
  • Loop the rope over the other points in numerical order as shown.
  • When the hitch is nearly complete, pull the rope to tighten all sides and tie it at point 1 (over the starting hitch) with a hitch or knot.
The bottom drawing shows the diamond hitch completed around a pack. Note the diamond in the center.
Back to Contents
Sheepshank
Sheepshank 1 not found Sheepshank 2 not found
Sheepshank 3 not found Used to shorten a rope that is fastened at both ends, and also to provide a purchase to run the rope thru to tighten that rope in a manner of a block and tackle (pulley):
  • Take up the slack as in 1.
  • Make an underhand loop as shown at B in 2, and slide it over the B1 bight and pull tight.
  • Do the same at the other end, to complete the knot.
  • To make more secure, add a second hitch at each end, as in 3.
Back to Contents
Marling
Marling not found Used by seamen to lash hammocks or other gear, marling is a series of overhand knots. The end of the rope should always come out from underneath the hitch.
Back to Contents
Toggles 1 not found Toggles 2 not found
Toggles
TogglesA toggle is a small piece of wood or metal usually used to lock a knot that may need to be loosened quickly or to help it hold more securely. Two examples are shown. At left is one end of a sheepshank with a toggle inserted to ensure the knot does not slip. At right is a lark's head with toggle. Removing the toggle releases the hitch.
Back to Contents
MarlinSpikeHitch not found
Marlin spike hitch
For a purchase on a rope before hauling on it. Can be used for tightening a lashing. For the spike use a marlin or a tent peg.
Back to Contents
Belaying 1 not found
Belaying
A means of attaching a rope to a cleat. Begin with a turn as shown, then make 1 or 2 fig-8 turns in the 2nd drawing. Finish with a hitch (underhand loop) pulled snug, unless the rope needs to be released quickly.
Back to Contents
RoundSeizing 1 not found RoundSeizing 2 not found RoundSeizing 3 not found
Round seizing
A seizing is a small lashing that binds 2 ropes or, sometimes, a lashing that holds a rope to a post. Seizings are often used to make a permanent eye in a rope. Cord or heavy twine can be used. To make a ropund seizing for an eye:
  • Form a bight.
  • Splice an eye in the end of the seizing material (see splicing). If the cord is too small, use a timber hitch.
  • Take 8 or 10 turns around both sides of the bight.
  • At the finish of the turns, bring the end down betweenthe loops and up thru the eye.
  • Snug up all the loops as shown and leave the end protuding as at A.
  • Take a 2nd series of turns, called riders, over the first ones, laying the turns in the grooves as shown at B. Do not pull them so tightly that they separate the first series of turns.
  • Finish the riders with a tuck-under as shown at D. This will leave the end as at C.
  • Take 2 or 3 frapping turns, see bottom drawing, to form a clove hitch.
  • Take the end down on to one of the ropes and fasten with another clove hitch.
Back to Contents
RackingSeizing 1 not found RackingSeizing 2 not found RackingSeizing 3 not found
Racking seizing
Used to lash together 2 parallel ropes:
  • Begin with an eye splice in the seizing material and then wrap it around the ropes in a fugure-8 pattern as in Fig 1.
  • Make as many turns as necessary.
  • Then bring the turns together as in Fig 2.
  • Wind round and round back toward the eye splice, laying the lashing into the spaces between the turns of the first set as indicated by the numbers in fig 2.
  • The seizing may be finished by making the same frapping turns and fastening used for round seizing.

Fig 3 shows the round seizing in cross-section; the fig-8 turns are shown by the white band and the round turns by the black band.
Back to Contents
Splices
Splices join ropes permanently while leaving the rope almost as strong as originally. The strongest is the short splice but it forms a swollen join which will not pass over a block. The long splice is a little less strong but the rope diameter remains the same.The eye splice and back splice have special purposes: the back splice preventing fraying or unraveling in the end of the rope, being more durable and lasting than whipping; the eye splice being the strongest type of rope loop.
ShortSplice not found
Short splice
Short splice:
  • If the rope is large, make temporary whippings on the ends of the strands.
  • Unlay (untwist) the ropes a few turns.
  • A. Alternate the strands of the 2 ropes.
  • B. Tie strands down to prevent more unlaying.
  • C. Tuck strand 1 over an opposing strand and under the next strand.
  • D. Tuck of strand 2 goes over strand 5, undr the 2nd, out between 2nd & 3rd.
  • E. Repeat for strands 1 & 3 from the same rope end.
  • F. Remove tie and repeat operation on other rope end.
  • Make 2 or more tucks for each strand, then roll the tucks and cut off the ends.
  • Smooth the splice by rolling on the floor under your foot.
Back to Contents
LongSplice not found
Long splice
Long splice:
  • A. Unlay each rope end about 15 turns. Place the 2 rope ends together, alternating tstrands of each end.
  • B. Using opposite pairs, unlay one end 4 and fill its place with the partner strand 2. Repeat exactly with another pair of strands 1 & 6 in oppositie direction.
  • C. Trim the longer strand 4 and tie each pair of opposing strands 2 & 4 with an overhand knot, tucking each strand twice. The tuck goes over one strand, under the 2nd, and out between 2nd & 3rd.
  • Strands 3 & 5 are simply tied with an overhand knot.
  • Strands 1 & 6 are halved, and opposite strands tied wihth an overhand before tucking.
  • D. Roll and pound all tucks into the rope and then clip the individual strand ends.
Back to Contents
BackSplice 1 not found BackSplice 2 not found BackSplice 3 not found BackSplice 4 not found BackSplice 5 not found BackSplice 6 not found
Back splice
Back splice:
  • Unlay to make a crown knot as shown in A, B & C.
  • The ends are then tucked as in the short splice with the same over-and-under movement. See D & E.
  • Finish by trimming the ends and smoothing the splice by rolling on the floor under your foot.
Back to Contents
EyeSplice 1 not found EyeSplice 2 not found
EyeSplice 3 not foundEyeSplice 4 not found
Eye splice
Eye splice:
  • Like the short splice, it is woven one over, one under. Strands may be loosened for tucking by twisting the rope in the direction opposite the lay.
  • A. Unlay the end 4 or 5 turns.
  • B. Tuck strand 2 over strand c, under b, and out between strands a & b.
  • C. Tuck strand 1 once over strand b & under a.
  • D. Tuck strands twice, as shown for strand 2.
Back to Contents
Lashings
For lashing or binding together timbers with rope.
It is important to use ropes of correct thickness and length:
As to length, figure 1m per 25mm of the combined diameter of the spars. Ex: when lashing 75mm and 100mm timbers together, you need 75/25 + 100/25 = 3m + 4m = 7m of rope.
DiagonalLashing 1 not found DiagonalLashing 2 not found
 
 
Diagonal lashing
Used to spring 2 spars together, that is, to join 2 spars which do not touch wher they cross:
  • Use a timber hitch where they cross. Tighten it to draw the the two close.
  • Take 3 or 4 turns around one fork; 3 or 4 around the other.The turns should be beside each other, not on top of each other.
  • Take 2 frapping turns about the lashing at the point where the spars cross, as in the lower drawing.
  • Finish with a clove hitch around either spar.
Back to Contents
SquareLashing not found
Square lashing
Used whenever spars cross at an angle, touching each other:
  • Place a clove hitch aaround the upright, directly below where the crosspiece will be. Tighten it.
  • Twist the free rope end and the standing part around each other to hold the loose end.
  • Wrap the rope behind the upright, down in front of the crosspiece, and around behind the upright. Do 4 times, keepingoutside the previous turns on the crosspiece and inside them on the upright..
  • Make 2 or 3 frapping turns between the timbers and strain tightly.
  • Finish with a clove hitch on the crosspiece.
  • Make all turns as tight and secure as possible.
Back to Contents
ShearLashing not found
Shear lashing
Used for forming shear legs of timbers with their butt ends spread apart, as in pioneering bridges:
  • Lay the spars parallel to one another.
  • Tie a clove hitch around one spar.
  • Bind 2 timbers by laying 7 or 8 turns around them, loosely, one turn beside the other.
  • Make 2 frapping turns around the lashing between the spars.
  • Fasten the rope end with a clove hitch around the 2nd timber.
  • Open out the 2 timbers to form the shear legs.
  • If the 2 spars are lashed merely to extend one of them (as in a flagpole) do not use frapping turns.
Back to Contents
TripodLashing not found
Tripod lashing
The middle leg is extended to the opposite direction to that of the outer legs:
  • Lay 3 spars on the ground, pointing in alternate directions.
  • Make a clove hitch or timber hitch around one of the outside spars.
  • Take 7 or 8 loose lashing turns around all 3 spars.
  • 2 frapping turns in the spaces between.
  • Finish with a clove hitch on the center spar.
  • Hoist the tripod into place.
Back to Contents
Climbing knots
See bowline, French bowline, bowline on the bight, running bowline.
A triple bowline is a normal bowline but uses a doubled rope to give 2 long thigh loops and a short chest loop for an unconscious person.
Add:
Back to Contents

Back to net & rope index